SABER Certificate forContactors & Overload Relays

Contactors & Motor Protection

Conformity-support guidance for industrial contactors and motor overload relays.

  • CertificatePCoC / SCoC*Product Certificate of Conformity & Shipment Certificate
  • PCoC CostUSD 300
  • Processing Time2–3 Working Days
  • SADAD FeesPaid by Importer

Product & Regulation

HS Code

HS 8536

Apparatus for switching or protecting circuits up to 1000 V. Equivalent apparatus above 1000 V falls under 8535. The Saudi code runs longer than four digits and is confirmed from the specification, not from the product name.

Regulation

IEC 60947-4 series where applicable; avoid broad IECEE claims

Candidate review point, not a declaration that this route applies. Confirmed against the current regulation and model scope before anything is claimed.

Product

Motor control contactors and thermal/electronic relays

What the assessment reads the product as, which decides the evidence it asks for.

Documents Required

  • Lab Test Report(No report? We can arrange testing.)
  • Commercial Invoice
  • Packing List

The core set. On this family the file also turns on aC utilization category, overload trip ranges, control voltage. Which further documents apply varies with the confirmed classification and the model scope, so the full list is issued per file rather than per category.

Sample Certificate

Illustrative layout only — not an issued certificate, and not a reproduction of one. Certificates are issued by approved conformity assessment bodies, not by BenzilaCert.

Application Examples

Typical files in this product family and the support they call for. Illustrative scenarios, not completed engagements.

  • Example 01

    Motor control contactor

    A motor control contactor, where the declared utilisation category sets the tests and every coil voltage variant has to reach the certified list.

  • Example 02

    Thermal overload relay

    A thermal overload relay, assessed on its trip class and current setting range rather than on the contactor it is paired with.

Get Your SABER Certificate

Send the Saudi HS Code if you have it, the product specification and a commercial invoice, and we will come back with the likely route and what is missing.

WhatsApp: +91 91300 30031No Advance Payment | Available 24/7

* Where applicable. Timelines and charges shown are indicative and subject to documentary review, and government and SADAD fees are separate from conformity body, testing and consultancy charges. The applicable Saudi regulation and the exact HS code must be confirmed from the product specification against the current SABER and ZATCA classification.
BenzilaCert is an independent consultancy providing application and documentation support. It is not SASO, SABER or a certificate-issuing authority, and does not issue conformity certificates.

Control Gear We Cover

This page covers the device, and the coordinated pairing, supplied as a product. Each family below carries its own evidence.

Three-pole power contactors

Motor switching contactors defined by utilisation category, rated operational current and control circuit voltage.

Mini and auxiliary contactors

Lower-rated contactors and control relays for interlocking and signalling, assessed at their own ratings.

Thermal overload relays

Bimetallic relays with a declared setting range. The trip class and the range are what define the model.

Electronic overload and motor-protection relays

Solid-state protection with wider setting ranges and additional functions, evidenced separately from bimetallic units.

Combination and reversing starters

Contactor and relay supplied as a pairing. The declared coordination behaviour belongs to the combination, not to either device alone.

Motor control centres — not this page

A finished MCC or control panel containing these devices is an assembly with its own ratings. That route is on our electrical panels page.

A starter is a combination, not a bigger contactor

The behaviour that makes a starter a starter — how the contactor and relay survive a fault together behind a declared protective device — belongs to the pairing. It is evidenced by coordination data for that specific combination, which is why a contactor certificate on its own does not establish a starter claim.

What Decides a Device's Classification

Six factors that separate one control gear file from another. Each is read from the declared ratings, not from the frame size.

Factors that determine how a contactor or overload relay is classified
FactorWhy it changes the answer
Device typePower contactors, auxiliary contactors, overload relays and starters are distinct families
Utilisation categoryThe declared AC duty determines the making and breaking tests and cannot be inferred from the frame size
Rated operational current and voltageCurrent and voltage ratings define the model family and constrain how far it can be grouped
Control circuit voltageCoil voltage and frequency variants are part of the model definition and appear on the certified list
Overload setting range and trip classFor relays, the declared range and trip class are the ratings the evidence has to support
Supplied as a device or as a combinationA contactor alone, a relay alone and a coordinated starter are three different submissions

We do not publish an HS code for control gear, because the code follows the device specification rather than the category. Contactors, relays, starters and parts can classify differently, and the classification is what determines the applicable regulation. It is confirmed per family — see our HS code check.

Saudi Certification Routes for Control Gear

What may apply to a control gear file, and what is confirmed per family rather than across the category.

Where the confirmed classification falls under an applicable Saudi technical regulation, control gear generally needs a product certificate registered on SABER, followed by a shipment certificate for each consignment. The product certificate is issued by an approved conformity assessment body against the technical file and the test evidence.

Control gear standards are split by device function, so the part that applies to a contactor is not the part that applies to an overload relay or to a coordinated starter. Which part the applicable regulation names is confirmed before the evidence is assembled, because it determines whether the reports on hand are the right ones at all.

Whether the IECEE route is available for a given device depends on the current national recognition scope. It does not follow automatically from the product being control gear, so we confirm it against the current published scope before relying on it.

The coil list is part of the product

A contactor range normally spans several control voltages and both frequencies. Each of those is a model variant, and a coil variant absent from the certified list becomes an uncertified item at the moment the invoice is read against the certificate.

Control Gear Testing Requirements

Checks a control gear assessment commonly draws on. Which apply depends on the device family and the standard part the regulation names.

Technical checks commonly applied to contactors, overload relays and starters
CheckWhat it looks at
Construction and clearancesCreepage, clearance and protection against electric shock
Temperature riseMain contacts, coil and terminals at declared operational current
Making and breaking capacitySwitching at the declared utilisation category and power factor
Operating limits of the control circuitPick-up and drop-out behaviour across the declared coil voltage range
Overload tripping characteristicRelay operation against the declared trip class and setting range
Dielectric strengthInsulation between circuits and to earth under applied test voltage
Mechanical and electrical enduranceDeclared operating cycles under load and no load
Short-circuit coordinationBehaviour of the starter combination with its declared protective device

Testing is carried out by laboratories accredited for the relevant tests. Endurance and coordination testing are the items that set the programme length, because both have to be run on the declared configuration rather than derived from a similar model.

Documents for a Control Gear Certification File

What a control gear submission is built from. Coil variants and coordination tables are the parts most often missing.

  • Confirmed Saudi HS code for each device family
  • Datasheet for each contactor, relay and starter model
  • Full model list with operational current, utilisation category and coil voltage per variant
  • Declared overload setting ranges and trip class for each relay
  • Coordination tables for starter combinations, as published for the range
  • Manufacturer name and address as they will appear on the certificate
  • Laboratory test reports to the standards the applicable regulation names
  • Coil variant list — voltages and frequencies supplied
  • Product photographs and the marking as applied to the device body
  • Statement of whether each model is also supplied inside finished control panels

Not sure your model list covers what you ship?

Send the catalogue extract with operational currents, utilisation categories, coil voltages and relay ranges, plus the reports you hold. We will map the certified list you need.

How a Control Gear File Progresses

Five steps from the device split to certified consignments.

  1. Separate devices from combinations

    A contactor, an overload relay and a coordinated starter are three declarations. They are split before anything else, because the evidence differs for each.

  2. Confirm classification and the applicable regulation

    Confirm the Saudi HS code per family, then the applicable technical regulation and which standard part it names for the device in question.

  3. Review the reports against the declared ratings

    Check what existing reports cover against the declared operational currents, utilisation categories, coil voltages and relay setting ranges.

  4. Complete the applicable conformity certification

    Prepare the technical file with the model list and coil variants, then submit for assessment by the approved certification body.

  5. Obtain shipment certification

    Each consignment is applied for against the product certificate, with the invoice models matching the certified list exactly.

What Drives Cost on a Control Gear File

Separate the government fees from the body, testing and service charges before comparing quotations.

Four things move the cost of a control gear programme: how many device families the catalogue splits into, how many coil and rating variants the certified list has to carry, whether coordination evidence exists for the starter combinations being sold, and the number of consignments needing shipment certificates.

Government and SADAD fees, conformity body charges, laboratory testing and service charges are separate lines and are quoted separately. Our SABER certificate cost page sets out how those lines work. We do not publish a flat price or a guaranteed turnaround for a control gear file, because both depend on the family split and the testing gap.

Where Control Gear Files Go Wrong

Six issues we see repeatedly on contactor and relay submissions.

AC-3 rating claimed from an AC-1 test

Motor duty and resistive duty are different tests at the same frame size. A rating declared for motor switching has to be supported by evidence at that category.

Coil variants missing from the model list

A contactor range usually spans several coil voltages and frequencies. Variants left off the list are uncertified items when the invoice is read.

Starter coordination assumed rather than published

A coordinated combination is declared against specific pairings. Without the coordination table, the starter claim cannot be read against evidence.

Relay setting range wider than tested

The declared setting range and trip class are tested properties. A catalogue range that reaches beyond the report is cut back at review.

Electronic and thermal relays submitted as one family

Bimetallic and solid-state protection behave differently and are evidenced differently, even where the setting ranges look comparable.

Devices covered only through a panel certificate

An assembly certificate for a control panel does not cover the same devices sold loose as spares. Stock shipped separately needs its own certificate.

Control gear certification questions

Family grouping, starter combinations, utilisation category, coil variants, existing reports and the shipment stage.

Do contactors and overload relays need SASO SABER certification for Saudi Arabia?

Where the confirmed Saudi HS code for the device falls under an applicable technical regulation, control gear generally needs a product certificate registered on SABER and then a shipment certificate per consignment. It is decided by the classification of the device rather than by the category name, so it is confirmed per family.

Can contactors and overload relays share one certificate?

They are distinct device families, commonly assessed against different parts of the control gear standard, so they are usually evidenced separately even when sold as a set. Variants within one family that share construction and standards can often be grouped across a rating range.

Is a starter certified as a device or as a combination?

As a combination. The declared behaviour of a starter — particularly its short-circuit coordination — belongs to the specific contactor, relay and protective device pairing, and is supported by coordination evidence for that pairing rather than by the ratings of the individual devices.

Does the utilisation category really change the file?

Yes. It determines the making and breaking tests the device is read against. A contactor declared for motor switching needs evidence at that duty; a rating established on resistive load does not transfer to it, even on the same frame.

Do coil voltage variants need to be listed separately?

They need to appear in the model list that the certificate covers. Coil voltage and frequency are part of the model definition, and a variant that is not on the certified list is treated as uncertified when the invoice is checked at the shipment stage.

Will my existing test reports be accepted?

Possibly in part. Reports to the standards the applicable regulation names, from a laboratory accredited for those tests, may support the file. Gaps are usually about the report scope against the declared categories and setting ranges rather than about the laboratory.

What is needed at the shipment stage?

The commercial invoice and packing list with model numbers exactly as certified, including coil variants, the product certificate reference, and the transport and origin documents. Our SABER documents checklist sets out the full list.

Find out what your certified list has to carry

Send the catalogue extract with operational currents, utilisation categories, coil voltages and relay setting ranges, plus any test reports you hold. We will review the family split and the evidence gap.

Get a Control Gear Certification Quotation

Tell us about the devices you ship, the coil variants in the range, and whether you sell coordinated starters. We reply within one business day with the likely route and what to send next.

Request a Free Quotation

The more we know about the product, the more precise the answer. Fields marked with an asterisk are required.

Datasheets, test reports, model lists or label artwork? Send them as PDF or images on WhatsApp after submitting — send your technical file documents for review. Please do not send SABER passwords or login credentials.

Datasheets, test reports, certificates or product photographs? Send them on WhatsApp after submitting — send your product documents for review. Please do not send SABER passwords or login credentials.