SABER Certificate forBus Duct & Busbar Trunking Systems

Industrial Busbar Systems

Bus duct, enclosed busway and busbar trunking for power distribution.

  • CertificatePCoC / SCoC*Product Certificate of Conformity & Shipment Certificate
  • PCoC CostUSD 300
  • Processing Time2–3 Working Days
  • SADAD FeesPaid by Importer

Product & Regulation

HS Code

HS 8536

Apparatus for switching or connecting circuits up to 1000 V. A trunking run supplied with distribution apparatus fitted may be read against 8537 instead. The Saudi code runs longer than four digits and is confirmed from the specification, not from the product name.

Regulation

IEC 61439-6 where applicable; project-specific safety and conformity route

Candidate review point, not a declaration that this route applies. Confirmed against the current regulation and model scope before anything is claimed.

Product

Busbar rating, insulation, busway joints and fire penetration design

What the assessment reads the product as, which decides the evidence it asks for.

Documents Required

  • Lab Test Report(No report? We can arrange testing.)
  • Commercial Invoice
  • Packing List

The core set. On this family the file also turns on bus duct rating, enclosure IP, joint design, manufacturer and installed configuration. Which further documents apply varies with the confirmed classification and the model scope, so the full list is issued per file rather than per category.

Sample Certificate

Illustrative layout only — not an issued certificate, and not a reproduction of one. Certificates are issued by approved conformity assessment bodies, not by BenzilaCert.

Application Examples

Typical files in this product family and the support they call for. Illustrative scenarios, not completed engagements.

  • Example 01

    Low-voltage busbar trunking

    A trunking run supplied with its joints and tap-off units, where the declared rating belongs to the assembled system rather than to a length of bar.

  • Example 02

    High-current industrial busway

    A high-current busway where the classification, the enclosure protection rating and the joint design are settled before the evidence is assembled.

Get Your SABER Certificate

Send the Saudi HS Code if you have it, the product specification and a commercial invoice, and we will come back with the likely route and what is missing.

WhatsApp: +91 91300 30031No Advance Payment | Available 24/7

* Where applicable. Timelines and charges shown are indicative and subject to documentary review, and government and SADAD fees are separate from conformity body, testing and consultancy charges. The applicable Saudi regulation and the exact HS code must be confirmed from the product specification against the current SABER and ZATCA classification.
BenzilaCert is an independent consultancy providing application and documentation support. It is not SASO, SABER or a certificate-issuing authority, and does not issue conformity certificates.

Trunking Systems We Cover

A trunking system is certified as a system. Each family below carries its own declared ratings and its own test evidence.

Sandwich-type busbar trunking

Compact insulated bar stacks for main risers and heavy feeders. Conductor material, insulation class and rated current define the system.

Air-insulated bus duct

Spaced conductors in a ventilated enclosure, used where short-circuit withstand and heat dissipation matter more than compactness.

Lighting and low-current trunking

Smaller systems with repeated tap-off points for lighting circuits and distributed loads, declared at their own rated current.

Tap-off units and plug-in boxes

Units that draw a load off the run. Where they contain protective devices, the declared rating of the unit is read separately from the run.

Joints, elbows, tees and expansion sections

Jointing is where a trunking system is weakest in service. Joint design and the declared tightening regime form part of the system declaration.

Switchboards and distribution boards — not this page

The assembly a run feeds into, or is fed from, is a separate product with its own ratings. That route is on our electrical panels page.

A run and the board it feeds are two products

Busbar trunking distributes power between points; a switchboard or distribution board distributes it at a point. They are assessed as separate products with separate declared ratings, and a certificate for one does not reach the other. Projects supplying both need both — the assembly route is covered on our electrical panels page.

What Decides a System's Classification

Six factors that separate one trunking file from another. Each is read from the declared ratings and the drawings, not from the catalogue name.

Factors that determine how a busbar trunking system is classified
FactorWhy it changes the answer
System typeSandwich, air-insulated and lighting trunking are distinct systems with distinct evidence
Rated current and conductor materialCopper and aluminium at the same rating are different systems and are type-tested separately
Rated short-time withstand currentThe declared short-circuit withstand is a primary rating and is tested on the jointed configuration
Enclosure and IP classIndoor, outdoor and wet-area classes change both the construction and the applicable tests
Fire penetration designWhere a run crosses a fire compartment, the barrier arrangement is declared and evidenced
Supplied as a system or as componentsA complete run with its joints and tap-offs is one submission; loose accessories can classify apart from it

We do not publish an HS code for trunking systems, because the code follows the system specification rather than the category. A complete trunking system, loose accessories and tap-off units containing protective devices can classify differently, and the classification is what determines the applicable regulation. It is confirmed per line item — see our HS code check.

Saudi Certification Routes for Trunking

What may apply to a trunking file, and what is confirmed per system rather than across the category.

Where the confirmed classification falls under an applicable Saudi technical regulation, a trunking system generally needs a product certificate registered on SABER, followed by a shipment certificate for each consignment. The product certificate is issued by an approved conformity assessment body against the technical file and the type-test evidence.

Busbar trunking is assessed as an assembly: the declared ratings belong to the configuration as installed, including its joints and tap-off interfaces. That is why the evidence asked for is type-test evidence on a representative jointed sample rather than a component report on the bar itself.

Whether the IECEE route is available for a given system depends on the current national recognition scope. It does not follow automatically from the product being electrical, so we confirm it against the current published scope before relying on it.

Project schedules are not certification evidence

Consultants specify trunking by rated current and short-time withstand on a single schedule line. Those figures become declarations on the certificate, so they have to match the type-test report rather than the design calculation that produced the specification.

Trunking Testing Requirements

Checks a trunking assessment commonly draws on. Which apply depends on the system type and the standard edition the regulation names.

Technical checks commonly applied to busbar trunking systems
CheckWhat it looks at
Temperature riseConductors, joints and enclosure at declared rated current
Short-circuit withstandThe jointed configuration against its declared short-time withstand rating
Dielectric strengthInsulation between phases and to the enclosure under applied test voltage
Protective circuit continuityEarth continuity across joints along the length of a run
Ingress protectionThe declared IP class, including at joints and tap-off openings
Mechanical strengthSupport spans, deflection and the behaviour of expansion sections
Fire resistance at penetrationsBarrier arrangement where a run passes through a compartment, where declared
Clearances and creepageSeparation distances inside the system and at tap-off interfaces

Testing is carried out by laboratories accredited for the relevant tests. Short-circuit withstand testing needs laboratory capability at the declared rating and a sample long enough to include a joint, which is why high-rated systems are the slowest part of a trunking programme to evidence.

Documents for a Trunking Certification File

What a system submission is built from. The variant list against the tested configurations is the part most often short.

  • Confirmed Saudi HS code for the trunking system and for accessories shipped apart
  • System datasheet with rated current, conductor material and withstand ratings
  • Full list of system variants — ratings, conductor sizes and enclosure types
  • General arrangement and run drawings, including joints, elbows and expansion sections
  • Joint design detail with the declared tightening regime
  • Tap-off unit schedule, with the protective devices fitted inside each one
  • Manufacturer name and address as they will appear on the certificate
  • Type-test reports covering the declared ratings on a jointed sample
  • Fire-barrier detail and supporting evidence where penetrations are declared
  • Product photographs and the rating label as applied to the system

Not sure the tested configuration covers your project?

Send the system datasheet, the declared ratings on the project schedule and the type-test reports you hold. We will map what the reports cover against what the project needs.

How a Trunking File Progresses

Five steps from the system definition to released project deliveries.

  1. Define the system, not the shipment

    A project ships metres of run, joints, elbows and tap-off boxes. The file is built around the system and its declared ratings, not around the bill of materials.

  2. Confirm classification and the applicable regulation

    Confirm the Saudi HS code for the system and for accessories invoiced separately, then the applicable technical regulation and the assembly standard it names.

  3. Read the type-test evidence against the declared ratings

    Check that the reports cover the declared current, withstand rating and conductor material on a jointed configuration, and identify what is missing.

  4. Complete the applicable conformity certification

    Prepare the technical file with the variant list and the run drawings, then submit for assessment by the approved certification body.

  5. Obtain shipment certification

    Each consignment is applied for against the product certificate, with the invoice lines reconciling to the certified system and accessory list.

What Drives Cost on a Trunking File

Separate the government fees from the body, testing and service charges before comparing quotations.

Four things move the cost of a trunking programme: how many system families and conductor materials the range splits into, how much of the declared rating range the existing type tests genuinely cover, whether withstand testing is needed at a high declared rating, and the number of project consignments needing shipment certificates.

Government and SADAD fees, conformity body charges, laboratory testing and service charges are separate lines and are quoted separately. Our SABER certificate cost page sets out how those lines work. We do not publish a flat price or a guaranteed turnaround for a trunking file, because both depend on the family split and the testing gap.

Where Trunking Files Go Wrong

Six issues we see repeatedly on busbar trunking submissions.

Copper evidence used for an aluminium run

Conductor material changes temperature rise behaviour. A report on a copper system does not support the aluminium equivalent at the same rated current.

Withstand rating tested unjointed

Short-circuit withstand is a property of the jointed system. Evidence taken on a plain length rarely survives review once the joint design is read.

Tap-off units left off the file

Plug-in boxes containing protective devices have ratings of their own. Omitted from the variant list, they surface as uncertified items at the shipment stage.

Invoice lines that do not reconcile to the certificate

Runs are invoiced by metre and by accessory. Where those lines do not map onto the certified list, the shipment application stalls.

Fire penetrations assumed to be covered

A barrier at a compartment crossing is evidenced, not inferred from the system certificate. Project consultants ask for it separately.

Project rating declared above the tested rating

The rating on a project schedule is sometimes read off a design calculation rather than the type-test report. Review uses the report.

Trunking certification questions

System versus parts, switchboard certificates, rating ranges, fire-stopping, existing type tests and the shipment stage.

Does busbar trunking need SASO SABER certification for Saudi Arabia?

Where the confirmed Saudi HS code for the system falls under an applicable technical regulation, a trunking system generally needs a product certificate registered on SABER and then a shipment certificate per consignment. It follows the classification of the system rather than the category name, so it is confirmed before the file is built.

Is a bus duct certified as a system or as separate parts?

As a system. The declared ratings belong to the run together with its joints, elbows and tap-off interfaces, and the type-test evidence is taken on that configuration. Accessories invoiced on their own lines still have to appear in the certified list so the shipping documents reconcile.

Does our switchboard certificate cover the busbar run it feeds?

No. A switchboard is an enclosed assembly with its own declared ratings; the trunking system that carries power away from it is a separate product. Projects supplying both need both, and the two certificates are read against each other at the interface.

Can one certificate cover a whole range of current ratings?

Only as far as the type-test evidence and the certification body allow. Trunking ranges are usually grouped by system family and conductor material, with the tested configurations anchoring the range. A single report rarely spans a catalogue from the smallest rating to the largest.

Who is responsible for fire-stopping where a run crosses a floor?

The barrier arrangement is declared with the system where it forms part of the product, but installation at the building is a site matter, and project consultants commonly ask for the product evidence and the installed detail separately. We confirm which part sits on the certificate before the file is submitted.

Will the manufacturer type-test reports we already hold be accepted?

Possibly in part. Reports to the standards the applicable regulation names, from a laboratory accredited for those tests, may support the file. Gaps are usually about the tested configuration — conductor material, joint design or withstand rating — rather than about the laboratory.

What is needed at the shipment stage?

The commercial invoice and packing list with the system and accessory descriptions as certified, the product certificate reference, and the transport and origin documents. Our SABER documents checklist sets out the full list.

Find out what your trunking certificate actually covers

Send the system datasheet with rated current, conductor material and withstand rating, the run and joint drawings, and any type-test reports you hold. We will review what the evidence reaches and what is missing.

Get a Trunking Certification Quotation

Tell us about the system you supply, its declared ratings, and the project it is going into. We reply within one business day with the likely route and what to send next.

Request a Free Quotation

The more we know about the product, the more precise the answer. Fields marked with an asterisk are required.

Datasheets, test reports, model lists or label artwork? Send them as PDF or images on WhatsApp after submitting — send your technical file documents for review. Please do not send SABER passwords or login credentials.

Datasheets, test reports, certificates or product photographs? Send them on WhatsApp after submitting — send your product documents for review. Please do not send SABER passwords or login credentials.