Pump Certification

SABER Certification for Submersible & Dewatering Pumps in Saudi Arabia

Exporting submersible or dewatering pumps to Saudi Arabia? BenzilaCert helps review the motor classification, control panel scope, accessory list and SABER certification requirements for each pump type.

Submersible pump with attached motor and cable, ready for installation

Send to scope a pump file:

  • HS Code Check
  • Motor & Rating Review
  • Model List
  • Accessory & Panel Review
Request Certification Assessment

Types of Submersible and Dewatering Pumps

A borehole pump, a sewage pump and a portable dewatering unit are not the same product for certification.

Submersible water pumps

Borehole and well pumps operating below the water level, where the motor enclosure, cable entry and ingress protection define the product.

Submersible sewage pumps

Designed to pass solids, usually with a cutter or vortex impeller. The duty, not just the power rating, distinguishes them from clean-water units.

Portable dewatering pumps

Site pumps for construction drainage and flood control, frequently supplied with a trolley, hose kit or integral control panel.

Submersible drainage pumps

Smaller units for basement, cellar and surface drainage — classified separately from large sewage or industrial pumps.

Pump control panels

Separately supplied motor starters, level controllers and VFD panels. Where invoiced as a separate article, the panel may carry its own classification.

Installation kits and accessories

Guide rails, base elbows, chains, coupling sets and discharge fittings shipped alongside the pump. Each item is checked on the invoice.

Saudi Regulations for Submersible Pumps

Classification depends on the pump type, the motor and the declared application.

Submersible and dewatering pumps may fall under machinery safety, electrical safety or other applicable Saudi requirements depending on the pump type, the construction, the motor and the application. The requirements are confirmed per product, not assumed from the product name.

See pumps certification for the wider pump category and machinery certification for the parent industrial equipment scope.

Motor Classification and Control Panel Scope

The question that shapes most submersible pump files.

The motor inside the pump is part of the product. But a control panel, a VFD or a motor starter supplied and invoiced separately may carry its own HS code and its own requirements. Do not assume the panel is inside the pump certificate — the scope is reviewed with the certification body.

Where the pump, the panel and the accessories all appear on one invoice, each item is checked. See electrical appliances certification for where a panel carries electrical requirements.

Check the invoice, not the catalogue

A guide rail, a base elbow or a chain may be part of the approved product or a separately traded item. How each appears on the commercial invoice determines how it is treated.

Information Needed for Pump Assessment

Eight data points that let an assessment start.

Technical data commonly requested for submersible and dewatering pumps
InformationExample of what to provide
Pump type and applicationBorehole, sewage, drainage, dewatering or mixed duty
Flow rate and headRated performance from the pump curve
Power and motor ratingkW or HP, phase, frequency, voltage and insulation class
Model listFull model or series list to be covered
Manufacturer and countryFactory name, address and country of origin
Materials and IP ratingCasing and impeller material, and ingress protection
Existing reportsSafety, performance or other reports already held
Invoice accessoriesPanels, kits, guide rails and similar items on the same invoice

Documents Required for Pump Certification

A preliminary list — the final evidence set depends on the pump type and the applicable route.

  • Product catalogue and technical datasheet
  • Confirmed Saudi HS code for the pump, and for any accessory invoiced separately
  • Nameplate photographs showing the rating data as it is marked
  • Motor specification: power, phase, frequency, voltage and insulation class
  • Complete model or series list to be covered
  • Manufacturer and factory details
  • Pump curve or rated performance data
  • Ingress protection (IP) rating evidence for submersible units
  • Relevant test reports already held
  • Control panel specifications — if invoiced separately
  • Saudi importer details, where the importer is appointed

Not sure if your control panel needs its own certificate?

Send the pump datasheet, the panel specifications and the invoice layout. We will confirm the scope before you apply.

How Pump Certification Works

Five steps, from product review to shipment documentation.

  1. Review the pump and its accessories

    Collect the pump details, the motor data, the accessory list and the proposed Saudi HS codes — including separate codes for anything invoiced on its own line.

  2. Confirm the product-specific requirements

    Screen the specification against the Saudi requirements in force for that product. A submersible sewage pump and a portable dewatering unit are not the same product for certification.

  3. Review the technical documents and evidence

    Check the datasheet, nameplate, motor data, IP rating evidence and existing reports against the scope the route calls for.

  4. Complete the assessment and coordinate the PCoC

    Where additional testing or assessment applies, arrange it, then submit for the product certificate through the approved certification body.

  5. Match models to the invoice and raise shipment documents

    Reconcile the certified models and accessories against the commercial invoice, then coordinate the shipment certificate with the Saudi importer.

Certification Cost and Timeline

Driven by the pump type, the model count and whether a panel or accessories classify separately.

The total depends on the SABER platform charges, the certification body’s review, any testing, and the agreed professional support. A pump invoice with a separately classified panel or accessory kit is usually more than a single-product file.

We quote per file and do not give guaranteed completion dates. See SABER certificate cost for how a quotation is itemized.

Common Pump Certification Problems

Six recurring issues in submersible and dewatering pump files.

Sewage pump declared as a water pump

A submersible sewage pump entered as a general water pump, or a dewatering unit grouped with borehole pumps. The application must match the actual product.

Control panel assumed to be inside the pump certificate

A separately invoiced panel is not automatically part of the pump scope. Where it arrives on its own line, the classification is checked separately.

Motor data incomplete

Power, phase, frequency, voltage and insulation class missing from the submission. Without these the motor cannot be matched against the applicable requirements.

Model list does not match the shipment

Models shipped that never appeared on the application — usually variants added after the certificate was issued.

Accessory kit not declared

Guide rails, base elbows, brackets and chains added to the carton after the scope was agreed. Every item on the invoice needs to be accounted for.

IP rating not supported by evidence

A submersible pump claims an IP rating on the nameplate, but the evidence on file does not cover ingress protection testing for the declared rating.

Pump certification questions

Control panels, model grouping, IP rating, installation kits, factory inspection and what a quote needs.

Does every submersible pump need the same SABER certification?

No. A borehole pump, a sewage pump and a drainage unit are different products for certification purposes. The classification depends on the pump type, the motor, the construction and the declared application.

Can a submersible pump and its control panel share one certificate?

Do not assume so. Where the panel is supplied and invoiced as a separate article it may carry its own classification. The scope is reviewed with the certification body rather than inferred from the fact that the two ship together.

Can several pump models appear under one PCoC?

Where models share a platform and the evidence supports the range, grouping is often possible. Markedly different constructions or ratings generally mean separate evidence and separate applications.

Is the IP rating tested independently for submersible pumps?

Where the applicable route requires it, the ingress protection rating must be supported by test evidence, not just a nameplate claim. What evidence is accepted depends on the certification body and the applicable standard.

What about installation kits shipped with the pump?

Each accessory is checked alongside how it appears on the invoice. A guide rail, base elbow or chain may be part of the approved product, a separately traded item, or something needing its own classification.

Is a factory inspection required for pumps?

Only where the applicable scheme requires it. It is not a general obligation for the category. Where it does apply it needs scheduling early.

What data do you need for a pump certification quote?

The pump type, rated specifications, motor data, model list, the manufacturer, the Saudi HS code if you have it, the accessory list and any existing reports. With those we can outline the likely route.

Get the pump scope right before you ship

Send the pump type, motor data, model list and accessory invoice. We will confirm which items need their own assessment and what evidence is missing.

Request a Pump Certification Assessment

Tell us the pump type, motor rating, model list and whether a control panel ships with it. We reply within one business day with the likely route and what to send next.

Request a Free Quotation

The more we know about the product, the more precise the answer. Fields marked with an asterisk are required.